Any referenced datasets can be downloaded from "Module downloads" in the module overview.
Project: Add Connectors and Wiring
Â
Â
Â
Â
Â
Â
Completion Time:Â Â 15 Minutes
Â
Prerequisites
        Completions of the Connectors Lesson
Â
Objective:Â Â In this exercise, you add and edit connectors, and add wiring. You complete the following steps:
        > Insert a connector using wire crossings for the pin spacing.
        > Insert a second connector, changing the pin orientation during insertion, and add wiring.
        > Split, stretch, and add pins to the connectors, and add wiring.
Â
Instructions
Â
1:  If the Project Manager is not displayed, on the Project tab, Project Tools panel, click Manager.
Â
Â
2:  If Schematic_Components_NFPA is the active project, skip to step 5. If it is open but not active in the Project Manager, do the following:
        > Right-click Schematic_Components_NFPA.
        > Click Activate.
        > Skip to step 5.
Â
3:  In the Project Manager, click Open Project.
Â
4:  Browse to where you installed the project files. Select Schematic_Components_NFPA.wdp. Click Open.
Â
5:  From the Projects list, click the expansion node next to Schematic_Components_NFPA to expand the drawing list in the manager.
Â
6:  Right-click Schematic_Components_NFPA_07.dwg. Click Open.
Â
7:  Zoom in to rungs 704 - 711 of the first ladder.
Â
8:  On the Schematic tab, Insert Components panel, Insert Connector flyout, click Insert Connector.
Â
Â
9:  In the Insert Connector dialog box, do the following:
        > For Pin Spacing, type "0.375"
        > For Pin Count, type "8"
        > Click At Wire Crossing.
        > Click Insert All.
        > Clear the Start Connector as Child check box.
        > Use the Rotate and Flip buttons as necessary to change the orientation to a vertical connector with the plug on the right.
        > Click Insert.
Â
10:  Select the insertion point for the connector on rung 704 just to the right of the TS-C terminal.
Notice how the pin spacing adjusts for the wire crossings and stays at the fixed value for the other pins.
Â
11:  Zoom in to the lower area of the first ladder, rungs 713 - 720.
Â
12:  On the Schematic tab, Insert Components panel, Insert Connector flyout, click Insert Connector.
Â
Â
13:  In the Insert Connector dialog box, do the following:
        > For Pin Spacing, type "0.375"
        > For Pin Count, type "10"
        > Select Fixed Spacing.
        > Select Insert All.
        > Use the Rotate and Flip buttons as necessary to change the orientation to a horizontal connector with the plug on the top.
        > Click Insert.
Â
14:  Before selecting the insertion point, press the TAB key. This flips the connector insertion.
Â
15:  Press TAB again. This reverses the pin numbering on the connector.
Â
Â
16:  Select the insertion point for the connector at "10.0, 6.0"
Â
Â
17:  On the Schematic tab, Insert Wires/Wire Numbers panel, click Multiple Bus.
Â
Â
18:  In the Multiple Wire Bus dialog box, click Component (Multiple Wires). Click OK.
Â
19:  In the drawing, select the pin connection points 1-6 on the plug side of connector PJ720. Press ENTER.
Â
Â
20:Â Â Click the left wire-connection point on input 17 to attach the wires to the PLC. Notice how the spacing of the wires changes to match the component.
Â
Â
21:  On the Schematic tab, Edit Components panel, Reverse Connector flyout, and click Split Connector. Â
Â
22:  Select the connector PJ720.
Â
23:  Click to select the split point between pins 6 and 7.
Â
24:  In the Split Block dialog box, do the following:
        > Click Jagged Lines.
        > Select the Reposition Child Block check box.
        > Click OK.
Â
25:  Select the position for the child connector on rung 712 above the multiple wires you just inserted.
Â
Â
26:  On the Schematic tab, Edit Components panel, Reverse Connector flyout, click Stretch Connector.
Â
Â
27:  In the drawing, select the bottom edge of PJ704.
Â
28:Â Â Select the new location point, stretching the connector far enough to add two more pins.
Â
Â
29:  On the Schematic tab, Edit Components panel, Reverse Connector flyout, click Add Connector Pins.
Â
Â
30:  In the drawing, select connector PJ704.
Â
31:  On PJ704, select locations for pins 9 and 10. Press ENTER.
Â
Â
32:  On the Schematic tab, Insert Wires/Wire Numbers panel, click Multiple Bus.
Â
Â
33:  In the Multiple Wire Bus dialog box, do the following:
        > For Horizontal Spacing, type "0.25"
        > Click Component (Multiple Wires).
        > Click OK.
Â
Â
34:  In the drawing, select the pin connection points 7 - 10 on the plug side of the child connector PJ720. Press ENTER.
Â
Â
35:  Before selecting the insertion point, move the cursor up and slightly to the left. Type F then press ENTER. This flips the wiring order between the connectors.
Â
36: Click the wire connection point of pin 7 on connector PJ704 to attach the wires.