What does it mean for a tool library name to be displayed in grey?

(Select one)

The library is not enabled and loaded.
The library is out-of-date.
The library contains new tools.
The library is not currently used in any document.

Select an answer

Which toolpath options can control how much time a tool spends above the part before cutting material?

(Select one)

Geometry.
Heights.
Passes.
Linking parameters.

Select an answer

When creating a 2D Pocket toolpath what will happen to the cutting depth if multiple faces are selected at multiple depths?

(Select one)

The toolpath will fail and require an individual selection.
Each face will be machined at its selected height.
All faces will be machined at the deepest faces depth.
All faces will be machined at the shallowest faces depth.

Select an answer

Why is it important to verify coolant levels and concentration before running a part?

(Select one)

It increases the machine's torque
It helps flush chips away and prevents tools from overheating
It prevents rusting of the machine
It slows down the machine's RPM

Select an answer

What is an aligned dimension creating a 2D sketch and applying a dimension between 2 points?

(Select one)

A dimension that will provide the maximum distance between the 2 selected points.
A dimension that is aligned parallel to the X-axis.
A dimension that is aligned parallel to the Y-axis.
A dimension that will provide the minimum distance between the 2 selected points.

Select an answer

What is the purpose of running the program in graphics mode before starting the operation?

(Select one)

To adjust the tool wear
To adjust the machine speed
To see where the tools should be starting and detect alarms
To measure the part automatically

Select an answer

What should you do before running the first tool in operation for the first time?

(Select one)

Press feed hold and verify distance to go and program positions
Skip the feed hold process if the part looks good
Lower the machine temperature
Increase feed rates to 100% immediately

Select an answer

Which modify tool can be used to great a tapered edge typically used to debur a part?

(Select one)

Fillet.
Offset Face.
Press Pull.
Chamfer.

Select an answer

Which statement best describes the drilling cycle Rapid Out?

(Select one)

The tool engages the material a small peck at a time, dwells for a period of time and rapids out to the feed plane before proceeding.
The tool engages the material at the specified federate and retracts at a rapid feedrate.
The tool engages the material a small peck at a time and rapids out to the feed plane before proceeding.
The tool uses a consistent pecking motion with micro rapid movements to evacuate chips while drilling.

Select an answer

Which display option can help identify if a tool has enough cutting flute to reach all geometry on a part?

(Select one)

Show tool.
Show in-process stock.
Show tool on cursor.
Show toolpath.

Select an answer

What tool is recommended to measure a 0.6-inch step during inspection?

(Select one)

Digital depth micrometer
Steel ruler
Tape measure
Calipers

Select an answer

What is the difference between a Fusion .F3Z file and a . F3D file?

(Select one)

A .F3D file contains only 3D designs while a .F3Z file contains toolpath data.
A .F3D file is 2D while a .F3Z file is 3D.
A .F3Z file contains multiple externally linked designs.
A .F3D file contains multiple externally linked designs.

Select an answer

If the corner of a model is sharp and a 2D chamfer toolpath is used, how is that displayed during a stock comparison simulation?

(Select one)

It is not displayed since it was not part of the original model.
It is displayed as transparent.
It is displayed as material left behind.
It is displayed as a collision.

Select an answer

If a hole is oversized during inspection, what should you check first?

(Select one)

Increase the RPM of the machine
Rerun the program without making changes
Check the coolant concentration
Check the tool used to create the hole, like the drill bit

Select an answer

Where can information about the mass of a part be found?

(Select one)

Selection tool.
Body properties dialog.
Modify Parameters dialog.
Measure tool.

Select an answer

Start your final test

Haas and Fusion 360 - CAD, CAM, and Part Programming final test

What does it mean for a tool library name to be displayed in grey?

Which toolpath options can control how much time a tool spends above the part before cutting material?

When creating a 2D Pocket toolpath what will happen to the cutting depth if multiple faces are selected at multiple depths?

Why is it important to verify coolant levels and concentration before running a part?

What is an aligned dimension creating a 2D sketch and applying a dimension between 2 points?

What is the purpose of running the program in graphics mode before starting the operation?

What should you do before running the first tool in operation for the first time?

Which modify tool can be used to great a tapered edge typically used to debur a part?

Which statement best describes the drilling cycle Rapid Out?

Which display option can help identify if a tool has enough cutting flute to reach all geometry on a part?

What tool is recommended to measure a 0.6-inch step during inspection?

What is the difference between a Fusion .F3Z file and a . F3D file?

If the corner of a model is sharp and a 2D chamfer toolpath is used, how is that displayed during a stock comparison simulation?

If a hole is oversized during inspection, what should you check first?

Where can information about the mass of a part be found?