Which icon is pictured next to the top-level component when a new component is created within it?

(Select one)

A small group of blocks
A single block
A block with a chain link
A block with a thumbtack

Select an answer

Which of the following analysis tools can be used to inspect shelled geometry inside a fully enclosed model?

(Select one)

Interference
Accessibility Analysis
Draft Analysis
Section Analysis

Select an answer

Which of the following would likely have no impact in the sustainability of a design choice?

(Select one)

Material Color
Physical Material
Weight
Service Life

Select an answer

When projecting model edges that are not on the active sketch plane, where are those projections created?

(Select one)

On a new construction plane midway between the plane with model edges and the active sketch plane
On the active sketch plane
On the plane that contains the model edges
On the Origin plane parallel to the plane containing the model edges

Select an answer

Which of the following statements regarding creased edges in the Form workspace is true?

(Select one)

They cannot be uncreased
They are the only edges that support the Insert Point tool
They can be uncreased
They are the only edges that can be used with the Bevel tool

Select an answer

Which of the following selection sequences is required to apply a symmetry constraint?

(Select one)

Selection sequence does not matter
First sketch entity, second sketch entity, symmetry line
Symmetry line, first sketch entity, second sketch entity
First sketch entity, symmetry line, second sketch entity

Select an answer

Which of the following operations can be used on an open profile sketch?

(Select one)

Surface > Patch
Sheet Metal > Flange
Solid > Extrude
Solid > Revolve

Select an answer

Which utility in the Form toolset can be used to fix start points on a Form body?

(Select one)

Convert
Display Mode
Enable Better Performance
Repair Body

Select an answer

At what stage during the creation of a Form body can symmetry be applied?

(Select one)

Only before Form creation
Only after Form creation
Symmetry cannot be defined for Form bodies, only solid bodies
Before and after Form creation

Select an answer

Which of the following occurs when a group of surfaces that form a closed region are stitched together?

(Select one)

They are converted to a solid body and the surface bodies remain in the Browser
They are turned into a rigid group of surface bodies
They are turned into a Selection Set comprised of surface bodies
They are converted to a solid body and the surface bodies are removed from the Browser

Select an answer

Which of the following Edit Form options can be used to assist with the gradual transition of geometry?

(Select one)

Display Detail Control
Fillet
Object Snap
Soft Modification

Select an answer

Which of the following is the correct representation of a 12mm User Parameter after it has been linked to a dimension?

(Select one)

#: 1200
fx: 1200
%: 1200
1200

Select an answer

Where in an active sketch can 3D Sketch functionality be enabled?

(Select one)

Marking Menu
Sketch Palette
Modify dropdown
Select dropdown

Select an answer

How can the entire loop of a tangent chain be selected while in the Form tool tab?

(Select one)

Right-click one edge in the tangent chain and select Match
Double-click one edge in the tangent chain
There is no such functionality, each edge must be selected manually
Long-press left-click one edge in the tangent chain

Select an answer

Which right-click option of a Joint in the Browser can be used to display the associated motion of just the selected joint?

(Select one)

Animate Model
Motion Link
Motion Study
Animate Joint

Select an answer

Which of the following is the best option to copy a component without retaining a link to the original?

(Select one)

Copy / Derive
Copy / Paste New
Copy / Create Component from Bodies
Copy / Paste

Select an answer

Which of the following options allows manipulation of the visual transparency of a component without changing the assigned look or material?

(Select one)

Appearance
Display Detail Control
Opacity Control
Physical Material

Select an answer

Where can a previously created section view be found?

Select up to undefined

Named Views folder in Browser
Analysis folder in Browser
Group in Timeline
Section views cannot be saved and viewed at a later time

Select an answer

Which of the following statements is true about defining User Parameters?

(Select one)

User Parameters can be driven by preexisting User Parameters
User Parameters can have more than one expression assigned to it at once
User Parameters cannot have math operators in its Expression
User Parameters cannot be defined without a description in the Comment field

Select an answer

Which of the following is true of a surface that is used for a Replace Face operation?

(Select one)

The surface must be orthogonal to the solid face it is replacing
The surface must have a surface area smaller than the solid face it is replacing
The surface must extend further than the solid face it is replacing
The surface must be touching the solid face it is replacing

Select an answer

What is the default Operation type for a closed profile in an Extrude operation that creates the first body of the design?

(Select one)

Intersect
New Body
Join
New Component

Select an answer

Which of the following is true of As-built Joints?

Select up to undefined

They can only define Rigid joint types
They automatically ground the associated components
They make use of the components’ current positions
The change the position of components based on snap point selections

Select an answer

What happens if a face on a solid body is deleted while in the Surface tool tab?

(Select one)

The face is unstitched from the solid body, and it becomes a surface body
The face is removed, and the solid body becomes an open surface body
Faces cannot be deleted using the Surface toolset
The face is removed and automatically patched, remaining a solid body

Select an answer

Which Utility in the Form toolset will attempt to average the size of divisions on a Form body?

(Select one)

Compute All
Convert
Make Uniform
Adaptive Mesh Refinement

Select an answer

Which of the following Section types can be defined in the Coil tool dialog aside from Circular?

(Select one)

Triangular Offset
Only Circular sections can be created with Coil
Hexagonal
Triangular External

Select an answer

How can the dimensions of a sketch be seen in the Design workspace when the sketch is not active?

(Select one)

The dimensions can only be seen when the sketch is active
Right-click the sketch in the Browser and select Look At
Right-click the sketch in the Browser and select Show Dimension
Right-click the sketch in the Browser and select Show/Hide

Select an answer

Which of the following icons appear on fully-defined sketches in the Browser?

(Select one)

Lock
Pencil
Thumbtack
Checkmark

Select an answer

Start your final test

Final test

Which icon is pictured next to the top-level component when a new component is created within it?

Which of the following analysis tools can be used to inspect shelled geometry inside a fully enclosed model?

Which of the following would likely have no impact in the sustainability of a design choice?

When projecting model edges that are not on the active sketch plane, where are those projections created?

Which of the following statements regarding creased edges in the Form workspace is true?

Which of the following selection sequences is required to apply a symmetry constraint?

Which of the following operations can be used on an open profile sketch?

Which utility in the Form toolset can be used to fix start points on a Form body?

At what stage during the creation of a Form body can symmetry be applied?

Which of the following occurs when a group of surfaces that form a closed region are stitched together?

Which of the following Edit Form options can be used to assist with the gradual transition of geometry?

Which of the following is the correct representation of a 12mm User Parameter after it has been linked to a dimension?

Where in an active sketch can 3D Sketch functionality be enabled?

How can the entire loop of a tangent chain be selected while in the Form tool tab?

Which right-click option of a Joint in the Browser can be used to display the associated motion of just the selected joint?

Which of the following is the best option to copy a component without retaining a link to the original?

Which of the following options allows manipulation of the visual transparency of a component without changing the assigned look or material?

Where can a previously created section view be found?

Which of the following statements is true about defining User Parameters?

Which of the following is true of a surface that is used for a Replace Face operation?

What is the default Operation type for a closed profile in an Extrude operation that creates the first body of the design?

Which of the following is true of As-built Joints?

What happens if a face on a solid body is deleted while in the Surface tool tab?

Which Utility in the Form toolset will attempt to average the size of divisions on a Form body?

Which of the following Section types can be defined in the Coil tool dialog aside from Circular?

How can the dimensions of a sketch be seen in the Design workspace when the sketch is not active?

Which of the following icons appear on fully-defined sketches in the Browser?