A model has several pockets that must be deleted. Which of the following is an efficient way to delete pockets?

(Select one)

Click each face to be deleted while holding the Shift key.
Click each face to be deleted while holding the enter key.
Use a window selection to only delete those features.
Use a crossing selection to only delete those features.

Select an answer

A simulated toolpath currently retracts and descends to different contours of the model before finishing clearing the area where it is located. How can this be optimized?

(Select one)

Enable Order By Area
Decrease Retract Height
Enable Stock Contours
Enable Rest machining from previous operations

Select an answer

A CNC programmer is machining a part and needs to ensure that all stock is removed, even the stock left from tool deflection. Which of the following options can be enabled to achieve this?

(Select one)

Repeat Finishing Pass
Use a conventional pass for the finishing pass
Increase the finishing pass feedrate
Use a negative stock to leave value

Select an answer

A part includes flat areas that need to be cleared that fall between the maximum roughing stepdown and the fine stepdown values. Which of the following allows for this?

(Select one)

Enable Flat Area Detection
Enable stock contours
Increase maximum roughing stepdown
Enable rest machining from previous operations

Select an answer

When preparing a model to act as starting stock, which of the following heals the surfaces of holes and edges?

(Select one)

Replace face
Press Pull
Surface patch
Delete Face

Select an answer

When you wish to quickly apply appropriate toolholders, which of the following can be effective?

(Select one)

Create a holder while creating the tool in the library.
Import a DXF file of the toolholder profile and revolve the profile as a form tool.
Import a solid model of the holder from the vendor’s website.
Create a toolholder library according to your personal machine configurations.

Select an answer

A part is being positioned within a vice. Which of the following is the correct configuration?

(Select one)

Stock material left within the vice jaws, with the part above the vice jaws.
Bottom of bard below vise jaws.
Bottom of part resting directly on vise jaws.
Bottom of stock above top of vise jaws.

Select an answer

On a setup sheet, where could you find information about the part size?

(Select one)

Under Setup
In the tool list
In the file name
In the operation list

Select an answer

A bullnose is machining a part and making excessive chatter. Which of the following might this indicate?

(Select one)

Excessive chip load
Stringy chips in the drill
The tool is leaving too much stock behind
The tool is hitting the vise jaw

Select an answer

A CNC programmer wishes to see if the toolpaths applied will leave gouges in a machined part. Which of the following Colorization options allows for this to be shown?

(Select one)

Model in simulation
Tool in simulation
Operation in simulation
Comparison in simulation

Select an answer

A Scallop toolpath is applied to a part. During simulation, the toolholder for the toolpath collides with the part. How can this be automatically mitigated?

(Select one)

Enable Detect tool length
Edit the tool and add a custom shaft segment
Edit the tool and change its length below the holder
Increase the flute length

Select an answer

A CNC programmer is preparing a tool library for a team project. Which of the following methods lets the library be shared to the team?

(Select one)

Save the library to a tools project that is accessible by the entire team.
Save the library to the cloud.
Sync the tool library using a third-party cloud sharing system.
Save the library to a read-only project file.

Select an answer

A CNC programmer is configuring a probe to help reset a work coordinate system. If they wanted to use a different probe for this operation, where could they find the option to do so?

(Select one)

The probe mode on the geometry tab
Right click on the probe operation and select edit tool
The select tool option on the tool tab
The cycle type on the linking tab

Select an answer

A toolpath currently has a maximum roughing stepdown of .75". Which of the following would smooth the rough steps?

(Select one)

A smaller Fine Stepdown value
A smaller Fine Stepup value
Order by area
Flat area detection

Select an answer

A CNC programmer needs to position a part within a digital vice. How can the part be positioned parametrically?

(Select one)

Use the Move command with the Point-to-point option.
Use the Joint command.
Use the Align command.
Create a rigid group.

Select an answer

A file has two setups, one for the front operation and one for the back operation. Roughing, finishing, and chamfering toolpaths have been applied to both operations. If you wanted to only post the code for the face and the chamfer of the front operation, which of the following would be a valid option?

(Select one)

Create an NC program and select only the roughing, finishing, and chamfering toolpaths
Create an NC program and select the first setup
Create an NC program for each of the desired toolpaths
Create an NC Program and select the second setup

Select an answer

A CNC programmer wants to configure a toolpath to descend directly into the part. Which of the following accomplishes this?

(Select one)

Set Ramp Type to Plunge
Increase ramp taper angle
Increase ramp diameter
Increase ramp taper angle

Select an answer

A team of designers and CNC programmers wish to ensure no burrs are found on a part after it is machined. Which of the following is best to record this kind of inspection?

(Select one)

Measurement input
Setting tolerances in Fusion 360
Pass/Fail
Bluetooth calipers

Select an answer

In order to accurately verify stock removal and toolpath features that do not exist on the model, which of the following should occur?

(Select one)

Set Colorization to Operation
Model visibility should be toggled off
Set Colorization to Model
Set Colorization to Comparison

Select an answer

A CNC programmer is preparing to machine a part and needs to edit the part to mimic starting stock. Which Workspace should this happen within?

(Select one)

Render
Animate
Design
Drawing

Select an answer

A CNC programmer is creating an NC Program to simultaneously machine the front and rear stations of a part using a dual station vise. They notice that the different tools are being used for the work offsets for both setups, and that the tools are running each work offset sequentially. If they wanted to save time so that both tools are used simultaneously in both setups using one program, what would be an effective option?

(Select one)

Enable Order by Operation
Rearrange the toolpaths in the order they should be machined
Enable Order by Tool
Enable Reorder to Minimize Tool Changes

Select an answer

A CNC programmer is creating a new CAM setup. How can they define the coordinate system used by toolpaths??

(Select one)

By creating a work point at the desired location that will be automatically selected in the setup.
By configuring the Work Coordinate System.
By moving the model to the design origin.
By importing a vise that has the Work Coordinate System preconfigured.

Select an answer

A part being machined has a toolpath that extends beyond the outer boundary of the part. How can this be modified?

(Select one)

Enable Rest machining from previous operations
Enable Rest machining from setup stock
Disable Stock Contours
Enable Stock Contours

Select an answer

A CNC programmer is setting up a probe to reset a work coordinate system based on machine surfaces. What would they configure If they wanted to probe the stock instead of the model?

(Select one)

The probe used for the probing cycle
Increase top height offset
Increase bottom height offset
The Probe Mode

Select an answer

A CNC programmer has several toolpaths applied to a part, but only needs to review the adaptive toolpath. How can this be achieved?

(Select one)

Choose the setup from the browser and then configure the Set Mode to All toolpath
Choose the proceeding toolpaths and adaptive from the browser and then configure the Set Mode to All toolpath
Choose the proceeding toolpaths and adaptive from the browser and then configure the Set Mode to Tail
Choose the adaptive toolpath from the browser and then configure the Set Mode to All toolpath

Select an answer

A part is being manufactured using a three-axis vertical machining center. In which direction should the Work Coordinate System Z-axis face?

(Select one)

Perpendicular to the top face of part towards the back of the machine
Perpendicular to the top face of the part towards the front face of the machine
Towards the top face of part
Away from the top face of part

Select an answer

A part has a 3D adaptive toolpath, but it does not reach certain parts. Which of the following can be applied to clear the remaining stock?

(Select one)

Use a smaller tool and specify a stock contour
Use a smaller tool and enable Continue machining from previous setup
Use a smaller tool and contain the toolpath using Slope
Use a smaller tool with rest machining from previous operations

Select an answer

When machining complex parts, which of the following is the benefit of creating a digital twin of the machining environment?

(Select one)

The WCS is created automatically.
The machining times will be more accurate.
The ability to determine the appropriate fixturing method and ensure collision avoidance.
Stock will be removed at a faster rate.

Select an answer

When using 3D Adaptive Clearing, a CNC programmer wants to limit operation of the machine to only remove material not yet removed by previous operations. How can this be accomplished?

(Select one)

Rest Machining
Slope Containment
Use a containment boundary
Enable stock contours

Select an answer

A CNC programmer is setting up stock for a model. After a stock selection method is complete, which of the following is the next step?

(Select one)

Orient the Work Coordinate System
Choose the Work Coordinate System location
Specify the model to be used in the setup
Check the stock against workholding equipment

Select an answer

A CNC programmer needs to create a partial 2D contour toolpath without creating a sketch to draw the required geometry. How can this be accomplished?

(Select one)

Project the required geometry onto an active sketch plane
Add a work point at the desired start and stop points
Use Open contour selection on existing model edges using chaining
Use Avoid Touch Surfaces to limit where the tool can cut

Select an answer

A CNC programmer needs to review the machining time and machining distance of a program. Which of the following displays that information?

(Select one)

Info tab in the Simulation dialog
Next to the setup in the browser
Display tab in the Simulation dialog
Statistics tab in the Simulation dialog

Select an answer

A CNC programmer needs to configure how the machine enters, exists, and transitions between toolpaths. How is this accomplished?

(Select one)

Linking options
Tool heights options
Tool containment boundary
Passes options

Select an answer

A part has both a parallel and a contour toolpath applied to a sloped area. How can the toolpaths be configured so they do not overlap?

(Select one)

Enable rest machining from previous operation
Enable Touch/Avoid Surface
Enable Slope
Contain the toolpath based on heights

Select an answer

A CNC programmer is preparing to machine a part that will have its profiled turned in a lathe before being moved to a mill. Which of the following is the best practice for preparing the model?

(Select one)

Revolve a sketch that represents the lathe profile, then continue to mill the part.
Define the stock as a fixed size tube when creating the setup.
Define the stock as a fixed size cylinder when creating the setup.
Duplicate the body to remove mill features for stock, then continue to mill the part.

Select an answer

A CNC programmer wants to tool a part, but they need for the toolpath to ignore interior slotting. How can this be accomplished in the most efficient way?

(Select one)

Use Avoid Surfaces to select the faces of the slot that are to be excluded
Delete the faces of the slot
Patch the slots and apply an adaptive toolpath

Select an answer

A CNC programmer needs to configure a toolpath so that the tool moves directly to the safest, lowest height where the tool clears the workpiece. How is this done?

(Select one)

Decrease the top height offset
Decrease the feed height
Enable minimal retraction
Decrease the bottom height offset

Select an answer

A CNC programmer wishes to create a toolpath with a maximum stepover that is equal to 20% of the tool diameter. How can this occur?

(Select one)

Enable Stock to Leave
Create a template with a stored stepover value
Manually calculate 20% of the tool diameter
Edit the Optimal Load expression

Select an answer

A CNC programmer wishes to machine all the stock of a part without limitation. Which of the following options allows for this?

(Select one)

Enable Stock Contours
Enable rest machining from previous operations
Enable slope
Set Machining Boundary to None

Select an answer

A CNC programmer is preparing the tools to be used in the library. The sample library includes a tool that could be used, but the diameter is inaccurate. Which of the following could be done?

(Select one)

A new tool should be created in the desired library.
The tool could be modified in the sample library.
The sample tool can be duplicated and modified.
The tool should be derived into the desired library.

Select an answer

A part needs a 2D contouring toolpath applied only to certain edges. Which of the following methods would be effective?

(Select one)

Use Avoid Surfaces to exclude the areas where the toolpath should not go
Create a sketch to contain the toolpath
Create a surface patch and set the surface patch as a model body to block the tool.
Use an open chain machining boundary

Select an answer

A part needs to be machined more efficiently. Which of the following would reduce movements in the Z-axis?

(Select one)

Increase clearance height
Enable a minimum retraction policy
Increase rapid feed rate
Increase retract height

Select an answer

When simulating a toolpath, the toolholder collides with the workholding. Which of the following can be changed to mitigate this?

(Select one)

The size of the toolholder can be updated
The part must be manufactured on another machine
The toolpath can be removed
The toolpath can be used to derive another operation

Select an answer

A CNC programmer needs to machine several parts and is concerned about the machine and tools incurring wear and tear. How can the engineer reduce wear and tear of the machine?

(Select one)

Use 2D Pocket with a large stepover and small depth of cut
Configure options for an Adaptive Clearing Toolpath
Use 2D Contour with a large depth of cut and stepover
Use a ball mill to rough the part

Select an answer

A CNC programmer wishes to inspect the Z location of a tool during a specific toolpath operation at a specific time in the operation. Which of the following allows for this?

(Select one)

Using the Simulation Player to slow simulation and reviewing the Simulation dialog
Enabling the show points option
Watching the Statistics tab while the tool runs
Setting the simulation Colorization to Comparison

Select an answer